---
title: "EIFS / ETICS Additives: Adhesive & Base Coat Mortar"
url: https://landuchina.eu/eifs-system-additives/
description: "ETICS/EIFS adhesive and base-coat additives (ETAG 004 / EAD 040083): Landercoll® HPMC/MHEC, Accurate® RDP and NOVASTAR® SHP for bond, crack bridging and frost."
author: "landuexpand@gmail.com"
date_published: 2026-05-19T06:39:24+00:00
date_modified: 2026-11-18T08:27:26+00:00
language: en-US
type: page
generator: LemonX AEO 1.4.12
---

# EIFS / ETICS Additives: Adhesive & Base Coat Mortar

EIFS / ETICS Additives for Adhesive, Base Coat and Finishing Mortars

Divider

Adhesive and base-coat additives for EPS, XPS and mineral-wool insulation systems.

LANDU: Your EIFS / ETICS Additives Manufacturer

Divider

An external thermal insulation composite system is only as good as its two thinnest layers: the 3–8 mm of adhesive that holds the insulation board to the wall and the 3–5 mm of base coat that carries the mesh and keeps rain out for 25 years. Both are polymer-modified dry mortars, and both pass or fail ETAG 004 / EAD 040083 on their additive package. This page sets out the Landercoll®, Accurate® and NOVASTAR® grades for each layer, the dosage ranges we start from, and the failures that European applicators report most often.

Three mortars, three briefs

Divider

| Layer | Function | Critical requirements (EAD 040083-00-0404) | Additive priorities |
| --- | --- | --- | --- |
| Adhesive mortar | Bonds EPS, XPS, mineral wool or wood-fibre boards to masonry or concrete | Bond to substrate ≥ 0.25 N/mm²; bond to EPS ≥ 0.08 N/mm² or board failure; tested dry, wet and after 2 h/7 d re-drying | Water retention on absorbent masonry, wet-out of EPS skin, open time for board adjustment, sag resistance under board weight |
| Base coat (reinforcing render) | Embeds glass-fibre mesh, bridges cracks, resists impact and weather | Water absorption < 1 kg/m² after 24 h for base coat and complete render; hygrothermal cycling (heat–rain, heat–cold) without cracking or debonding; impact category I/II/III; freeze–thaw where required | Flexibility (crack bridging), hydrophobicity, adhesion to EPS/MW, pumpability for machine application |
| Finishing render / decorative coat (mineral) | Colour, texture, weather skin | Water absorption, vapour permeability, freeze–thaw | Workability, open time for floating, water repellency, efflorescence control |

The same cellulose ether grade can serve all three layers; the polymer powder and hydrophobic components change layer by layer.

Grade selection

Divider

**Landercoll® cellulose ether.** Every grade below carries EIFS / ETICS on its technical data sheet: K100H ("EIFS and standard tile adhesives"), K150 ("EIFS/EITCS, tile adhesives, skim coat"), K200 and K200H ("tile adhesives, EIFS/EITCS, skim coat"), K40H ("premium tile adhesives and EIFS"), EM40HT ("EIFS — surface mortar and adhesive mortar"), EM100H ("cement-based tile adhesives and EIFS") and EM200 ("tile adhesives, EIFS/EITCS"). K75 and EM80 are the cement render grades used for mineral finishing coats. Viscosities are Brookfield RV, 2 % solution, 20 °C.

| Mortar | Grades (viscosity) | Starting dosage | Why |
| --- | --- | --- | --- |
| Adhesive mortar, hand-applied | K150 (55,000–65,000) · K200 (65,000–80,000) / EM200 (65,000–80,000) | 0.30–0.40 % | Water retention "very high" (K150) and sag resistance "excellent" (K200, EM200) for board weight on brick and AAC |
| Adhesive mortar, machine-applied | K100H (45,000–60,000) / EM100H (45,000–60,000) | 0.30–0.40 % | Pumpable viscosity with high water retention; EM100H sag resistance "excellent" |
| Base coat, hand and machine | K100H · K40H (20,000–24,000) / EM40HT (18,000–23,000) | 0.25–0.35 % | Smooth mesh embedding, no sag at 4–5 mm; EM40HT is the TDS grade for EIFS surface mortar |
| Base coat for Southern Europe / summer | EM40HT · EM100H (HEMC) | 0.30–0.40 % | Heat resistance "excellent" on the HEMC TDS versus "standard" for HPMC |
| Mineral finishing render | K75 (35,000–40,000) / EM80 (35,000–45,000) | 0.15–0.25 % | Cement render grades: float finish, texture stability |

**Accurate® redispersible polymer powder**

| Mortar | Grade family | Grades (TDS Tg / MFFT) | Starting dosage |
| --- | --- | --- | --- |
| Adhesive mortar to EPS/XPS | Rigid or semi-flexible VAE | 5011N (Tg 10 ± 5 °C / 4 °C; TDS: adhesive and surface mortar for EIFS), 4025N (Tg 0 °C / 1 °C; TDS: adhesive mortar for EIFS) | 2–3 % |
| Adhesive mortar to mineral wool / wood fibre | Semi-flexible | 4025N | 3–4 % |
| Base coat, standard (impact cat. III/II) | Flexible | 5045N (Tg −10 ± 5 °C / 0 °C; TDS lists EIFS), 9055E acrylic–silane (Tg −15 °C / 0 °C) | 3–5 % |
| Base coat, high impact (cat. I) or renovation on old render | Flexible + strong hydrophobic | 5045N + 8035H (TDS: adhesive & base-coat mortars, mineral renders) | 5–8 % total |
| Base coat with declared low water absorption | Hydrophobic | 8035H (strong hydrophobic effect), 8048H (very strong, instant-dissolving) | 3–5 % |
| Mineral finishing render | Semi-flexible or hydrophobic | 4025N, 8035H | 1–2 % |

**NOVASTAR® specialty additives**

- SHP75 / SHP80 silicone hydrophobic powder, 0.2–0.5 % (TDS range 0.1–0.5 %): the TDS names EIFS, stucco and façade render among its applications — it reduces capillary water transport and 24 h water absorption of base coats and finishing renders while keeping vapour permeability, with limited impact on mechanical properties.
- Starch ether ST3511, 0.03–0.08 %: the TDS grade for "EIFS/ETICS insulation mortars, adhesive mortars and putty" — residue on ignition ≤ 1 %, neutral pH, improves wet adhesion and workability. ST3547 (universal grade for adhesive and thermal-insulation mortars) adds anti-sag under heavy boards.
- PP fibre 3–6 mm, 0.05–0.15 %: plastic-shrinkage crack control in base coats applied in wind and sun.
- Powder defoamer P805, 0.1–0.2 % (P806 alkali-resistant, P807 low-temperature): denser base coat, fewer pinholes in machine-sprayed layers.

Dosages are percentages of the total dry mix for laboratory starting points; the technical data sheets do not prescribe dosages. Verify against ETAG 004 / EAD 040083 test methods with your cement and sand.

Troubleshooting reported by ETICS applicators

Divider

| Symptom | Likely cause | Adjustment |
| --- | --- | --- |
| Boards debond with clean EPS surface | Mortar skinned before the board was pressed; low polymer | K200H or EM40HT at 0.35–0.40 % for water retention; RDP ≥ 2.5 %; check EPS surface is dust-free and not UV-degraded |
| Boards slide after placement | Low sag resistance | 0.05 % ST3547; K200 / EM200 instead of K100H (sag resistance "excellent" on the TDS); reduce water |
| Cracks along mesh overlaps | Base coat too thin at overlap; rigid polymer | Minimum 3 mm cover over mesh; flexible 5045N / 9055E ≥ 3 %; 0.1 % PP fibre |
| Map cracking of base coat in summer | Fast water loss on EPS in sun | HEMC EM40HT or EM100H (heat resistance "excellent"); shade and mist-cure; fibre |
| Water uptake > 1 kg/m² at 24 h | No hydrophobic component; high w/c | SHP 0.3 %; hydrophobic RDP 8035H; lower water with ST3511 |
| Efflorescence on finishing render | Soluble salts carried by water movement | SHP 0.3–0.5 %; hydrophobic RDP; low-alkali cement |
| Pump blockage, pulsing output | Water retention drops under pump pressure; air | EM100H / EM40HT; defoamer P805; consistent water dosing |
| Freeze–thaw spalling of base coat | Low polymer, high air, water uptake | RDP ≥ 4 % flexible; SHP; defoamer |
| Biological growth, dark streaks | Surface stays wet | Hydrophobic additives; finishing render with lower water absorption |

Related guides: [EIFS adhesive formulation guide](https://landuchina.eu/eifs-adhesive-formulation-guide/) · [Improving bonding strength in EIFS adhesives](https://landuchina.eu/how-to-improve-bonding-strength-in-eifs-adhesives/) · [What is an EIFS system](https://landuchina.eu/what-is-eifs-system/) · [5 Common EIFS Adhesive Problems Seen on Site](https://landuchina.eu/eifs-adhesive-problems-on-site/).

Climate notes for European formulators

Divider

- **Nordic and Central Europe**: freeze–thaw and driving rain dominate. Prioritise flexible RDP at the upper end of the range, hydrophobic powder in base coat and finish, and air content below 12 %.
- **Atlantic coast**: long wet periods — hydrophobicity and vapour permeability together; avoid film-forming additives that seal the surface.
- **Mediterranean**: open time and plastic shrinkage — HEMC grades (EM40HT, EM100H), fibre, and shading during application.
- **Renovation on existing render**: adhesion to weak, chalky substrates — semi-flexible 4025N at 3–4 % in the adhesive and a bond-test (pull-off) before system approval.

Starting formulations (dry mix, laboratory basis)

Divider

| Component | Adhesive mortar | Base coat |
| --- | --- | --- |
| CEM I / CEM II 42.5 | 30–35 % | 25–30 % |
| Hydrated lime | 0–5 % | 3–5 % |
| Quartz sand 0.1–0.6 mm | 55–60 % | 55–60 % |
| Limestone filler / lightweight filler | 5–8 % | 5–10 % |
| Landercoll® cellulose ether | K150 0.35 % | EM40HT 0.30 % |
| Accurate® RDP | 4025N 2.5 % | 5045N 4 % |
| NOVASTAR® starch ether ST3511 | 0.05 % | 0.03 % |
| NOVASTAR® SHP75 / SHP80 | — | 0.3 % |
| PP fibre 6 mm | — | 0.1 % |
| NOVASTAR® defoamer P805 | — | 0.15 % |

Starting points only; the board type, substrate and target impact category determine the final polymer and hydrophobic dosage.

Products referenced on this page

Divider

- [Landercoll® HPMC for EIFS/ETICS](https://landuchina.eu/products-and-solutions/hpmc-for-eifs-etics-systems/) · [Landercoll® MHEC for EIFS/ETICS](https://landuchina.eu/products-and-solutions/mhec-for-eifs-etics-systems/)
- [Accurate® RDP for EIFS/ETICS](https://landuchina.eu/products-and-solutions/rdp-for-eifs-etics-systems/) · [Accurate® RDP range](https://landuchina.eu/products-and-solutions/china-rdp-powder-supplier-landu-accurate-high-performance-customizable-solutions/)
- [NOVASTAR® SHP silicone hydrophobic powder](https://landuchina.eu/products-and-solutions/novastar-specialty-additives/novastar-shp-the-ultimate-silicone-hydrophobic-powder-for-building-protection/)
- [NOVASTAR® HPS starch ether](https://landuchina.eu/products-and-solutions/hydroxypropyl-starch-ether-hps/) — ST3511, ST3547 · [PP fibre](https://landuchina.eu/products-and-solutions/polypropylene-fiber/) · [Powder defoamer](https://landuchina.eu/products-and-solutions/powder-defoamer/)

Supply for European ETICS manufacturers

Divider

LANDU manufactures Landercoll® cellulose ethers, Accurate® polymer powders and NOVASTAR® additives in three plants in Shandong (75,000 t/year) and has supplied dry-mortar producers in Europe since 2011. All grades are REACH-compliant and produced under ISO 9001; batch certificates follow every shipment. Stock is held with partners in several European countries, including Greece, Spain and Italy, for call-offs below a container; factory lead time is 7–15 working days. Packaging per TDS: 25 kg bags with PE inner liner, 500–600 kg pallets for cellulose ether and 600–1,300 kg pallets for RDP, neutral or OEM bags on request. Our application laboratory runs pull-off tests on EPS and mineral wool, water absorption and freeze–thaw screening on customer formulations.

Manufacturing & Production

See LANDU's production facilities, manufacturing processes and industrial additive portfolio.

Divider

View LANDU Factory

Quality Control & Assurance

Review LANDU's approach to raw-material inspection, process control, batch tracking and finished-product testing.

Raw-material inspection

Process control and batch tracking

Finished-product testing

Divider

Explore Quality Control

TDS, SDS & Batch COA

A Technical Data Sheet (TDS) describes the specifications and technical characteristics of a product grade. A Certificate of Analysis (COA) reports measured results for an identified production batch. Both documents support raw-material evaluation alongside application testing.

Contact LANDU about technical documents and batch-specific COA information for your selected material.

Technical Data Sheets (TDS)

Safety Data Sheets (SDS)

Batch Certificates of Analysis (COA)

Divider

Request Batch COA & Technical Data

EIFS / ETICS Additives: Frequently Asked Questions

Divider

Answers on additive selection, testing, samples and supplier qualification.

How to Change my Photo from Admin Dashboard?

Far far away, behind the word mountains, far from the countries Vokalia and Consonantia, there live the blind texts. Separated they live in Bookmarksgrove right at the coast

Request Samples and a Grade Recommendation

Divider

Send us your adhesive and base-coat recipes, the board types you bond and your target impact category.

We return grade recommendations and dosages within two working days and ship samples free of charge.

REQUEST SAMPLES

**[Ask a Formulation Engineer](https://landuchina.eu/contact-us/)**

*LANDU — Committed to Every Gram.*
